Відео

Did this mod work

Thanks for showing how you raised your garage ceiling. I am about to do the same so that I can raise my vehicles higher so I may stand, not squat under them to work. I 'm only modifying four of the trusses so I may take advantage of getting the vehicles to the height so no longer have to squat under when doing Maintenace on them. Thanks for showing how you did yours. I'll be working with engineers to make sure I do it correctly, so not to have roof falling or worse.

I have the same noise on my 2015 6.2 Denali since I bought it new. are you sure it's the lifters?

Thank you for the detailed approach to modifying trusses. I have removed a 12’x10’ heavy rolling barn door & installed an insulated panel garage door. Not enough room for the opening mechanism. I prefer your approach to the scissor truss modification. As a Canuck living in WV it was also nice to hear Ottawa & Belleville being mentioned. Thanks again.

Did you rvt the seal ?

Did you ever complete the swap?

Parts zilla has new oem

It's a no for me due to the manual dump.

Try 91 Octane. 6.2 recommends 91 not 87

Nothin like back country riding with a wheelbarrow only in Canada

Do you always drive that fast? Maniac

How wide is this unit

Just got a twin to this today. Have you run into any major issues!

Give it some ls3 heads and people tbink it has a corvette engine.

Rather than scoop out by hand what won;t dump out by itself, I simply grab the dump handle and work it back and forth to kinda bounce the remains out while it's in full dump position. That works great for me. I also onder about using the forward inertia of the machine as it comes to a full stop to help flip the dump forward? But there would need to be a cable and lever hooked up to the dump release mechanism that would have to be up on the handle bar to enable this.

Ive had mine for a few years and I've had issues with the clutch handle bending/breaking twice so far. The handle is made from stamped steel and eventually gives out after awhile due to such a strain on it and weak design. Princess Auto can order you a new one but supply of them can be spotty so my advice is order one (or two) before you need them, because mine was down for mths while I awaited a new one. But they are cheap ,both in cost and design, and I just replaced it again. They are also tricky to replace due to a fairly complicated design that has fastened to the machine handlebar by bolts that run up though the left side brake control bracket on the underside of the handlebar.

I'm thinking of making a track machine for kids with this.

Dear, is there a beering in side around a culmen??

Would you still do it if it only has 1 of the holes?

HI i was planning to do simple adaptation on a GME Rascal F10A looking for some informations to put a G16BB or something else if it's not too complicate... Just looking how to do it ?

Thanks Man!

when the primary closes, the belt moves towards the engine

What other modifications did you have to do there than adapter harness

My nytro broke down yesterday in the driveway, thought it was the belt at first... Shouldn't I be able to turn the primary by hand? thanks

How t repair

Handsame machine

its basely pretty nice

🥱 ssslow

I'm in the process of buying a 2015 yamaha sr viper xtx se 141 I've had a 97 vmax 700 triple sx for a long time with no issues but decided to get this newer one . What's all I should look at before I load it up and take it home . Thanks

'PRINCESS AUTO'------The pride of Winnipeg, Manitoba, Canada-------Started by Mr Tillman on Princess St with a tow truck.

It’s one of those Frankensteined G20 cutaway van Winnebagos. Looks like they grafted Dodge headlights into the nose!

Where in canada are you located? I need work done on my speed6

Did you ever find what the issue was with this?

Made in China?

Stock ?

Nice run! My 2012 mdx ran 15.42 at 90.52 mph

Hopefully you put a groove in the oil seal outer mating surface with your pin punch! Your technique is so smooth and not at all crude!!!

high flow third cat? which cat did you use??

Your John deere broken? A loader attachment would be far faster to use and do much more for far less cash

lmao. lock downs.

I was thinking about buying this last week, glad i did not. That dumping issue and not dumping completely is a no go. Toi bad because the rest of the machine looks nice.

That's cheating sir !

I spent 2 hrs at Canadian tire looking for the right bolt to go in the crank still haven’t found one

Replace your rubber value stems with metal values, the liquid will weaken the adhesive on the rubber value stem core and it will eventually fail, guaranteed. 😢 I just went through that with my 1025 R turf tires loaded with Rim Guard. Informative video, nice job!

You mention the machinenis a little light in the back end. Ive seen videos of similar machines that have steps behind the motor so the operator can stand/ride. Do you think this machine could handle a rider standing behind the motor if some steps were fabricated?

Hey mate, how did you get on in the end? Dying to see the rest of this series

Absolutely scrap and dangerous kept tipping over don’t buy

those things really start to shine when you have to haul 250 loads of gravel up a big hill.

Put a double small hydraulic arm(s) under neath. Smoove operationnnn.

I can use one I don't really need one but seeing this video I want one Seeing it goes through bush well I'd rig it up to pull logs out of the woods